Start Now

 

Are you currently trying to find suggestions concerning Tools You Need to Install a New Bathtub ?

Mounting a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old tub with a brand-new one is also a moderately hard project. If the old tub is conveniently accessible, the job can relocate quickly; if you need to open up a wall to remove the old bathtub and also position the new bath tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old bathtub and embeded in the new one. Make certain you have certified on your own for the task as well as are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is far better to take into consideration using one before you begin. Opportunities are you might need a professional plumber to make tube links.
This short article will aid you set up a new bath tub in your shower room if you have currently gotten a new bathtub and do not need to alter the setup of your previous water pipes.
Your devices and product checklist must consist of the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Planning for the Installation

First of all, the supporting structure provided with the bathroom ought to be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final position.

 

 

Removing Old Touches

If you require to replace old taps with new ones as a part of your installment, then the first thing you ought to do is detach the water supply. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.

 

 

Setting up the Tub

Utilizing the two wooden boards under its feet, place the bathtub in the called for position. The wood boards are useful in evenly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bathtub till the spirit level reviews level.
To install faucets, fit all-time low of the furthest flexible faucet connector to the suitable supply pipeline by making a compression join; then do the same for the various other tap.
Activate the water and inspect all joints and brand-new pipework for leakages and tighten them if essential. Fill up the bath tub as well as additionally check the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bath paneling as described in the maker's instruction manual. Tiling and sealing around the tub needs to wait till the tub has actually been utilized a minimum of when as this will resolve it right into its last setting.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, after that you will certainly need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers remain in area in between the faucet and also the sink. Safeguard the faucet in place with the maker provided backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former type must be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Tub

In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, causing the water to penetrate the wall in between the bath and the tiling, resulting in problems with dampness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes and also cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill the bathtub with water before securing, to permit the motion experienced when the tub is in usage. The sealer can fracture rather very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water resistant adhesive and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you really like reading up on How to Install a Bathtub Yourself? Try to leave a comment directly below. We'd be pleased to see your opinion about this posting. We hope that you come back again in the near future. Sharing is nice. Who knows, you will be helping someone out. Many thanks for your time spent reading it.

Instant Quote